Skip to content
Professional tracker · NB-IoT

GPS tracker ULTRA N
Essential NB-IoT, up to 10 years battery life

GPS · GALILEO · BLE 5.0 · NB-IoT

A rugged NB-IoT tracker optimised for outdoor and in-transit assets. Accurate GNSS positioning outdoors, zone-level accuracy indoors through BLE beacons. Up to 10 years of battery life, with no SIM card.

Up to 10 years IP68 & IP69K IK09 10,500 mAh replaceable Europe & USA CE · FCC
TRAKmy ULTRA N 1141 GPS tracker – long-life NB-IoT
IP69K
Max. ingress protection
10,500 mAh
Li-SoCl₂ replaceable
NB-IoT
No SIM card
5–10 years
Estimated battery life
IP69K
Maximum ingress protection
-20/+60°C
Temperature range
3-in-1
GNSS · BLE · NB-IoT
Automatic indoor and outdoor positioning
Positioning

100% indoor
& outdoor

The tracker switches automatically to the best technology for the environment. No manual configuration.

Multi-constellation GNSS, GPS + GALILEO
Accurate outdoor positioning with GPS + GALILEO. Indoors, it switches to BLE beacons for zone-level accuracy.
Priority sequence configurable over the air
A fully configurable profile, changed remotely over NB-IoT or BLE, with no physical handling.
Sensolus beacon detection
Compatible with Sensolus BLE beacons. Accurate zone positioning as soon as a beacon is detected in range.
Adaptive tracker behaviour
On-board intelligence

Adaptive
behaviour

The tracker adapts its behaviour to the context automatically. Departure, arrival, dead zone: all handled.

Departure & arrival detection
Reporting intensity adapted automatically. Faster reaction for a more efficient supply chain.
Smart dynamic positions
Reporting steps up on approach to destination, and switches to periodic mode on rail or in a dead zone.
Guaranteed data recovery
Cellar, open sea, no-network zone: data is stored on board and reported automatically once coverage returns.
GNSS positioning technologies and BLE beacons
Indoor accuracy

BLE beacons
for indoor use

Install Sensolus BLE beacons in your indoor areas for accurate zone positioning without GPS.

Sensolus BLE beacons
Install a beacon in each zone to locate your assets precisely inside warehouses and workshops.
Configurable zone accuracy
Define your working zones once: the tracker detects its presence automatically and reports the location.
WHEN SHOULD A POSITION BE SENT? Movement On departure and on stopping Auto detection Periodic Every X hours / minutes e.g. every 3 h Scheduled At specific configured times e.g. daily at 8 am Context On a detected change of state Tilt · tamper Config OTA
Full configurability

Fully
configurable over the air

Every aspect of the tracker's behaviour is configurable remotely, with no physical handling and no site visit.

Positioning frequency and conditions
Motion-based, periodic or scheduled. Update rate and journey detection fully configurable.
On-board rules engine
Define business rules directly in the tracker: departure/arrival alerts, activity thresholds, dead-zone handling.
Sensors

3 built-in sensors as standard

Activity, orientation and tamper protection: all native, with no additional wiring.

Activity
Sub-minute measurement of movement and vibration to calculate the real operating hours of your assets.
Sub-minute accuracy · OTA
Orientation
Detects the orientation and tilt of the asset. Alerts if the tracker is turned over or tilted abnormally.
Configurable · Real time
Virtual tamper
Detects handling or removal attempts with no physical sensor. Fully configurable software algorithm.
Configurable algorithm · OTA
Comparison

ULTRA N vs ULTRA N+
Which tracker should you choose?

The ULTRA N and the ULTRA N+ share the same casing, the same battery and the same platform. The difference comes down to 3 key features that determine the right choice for your assets.

ULTRA N (this page) ULTRA N+ → see the page
Reference TRACK 1141 TRACK 1101
Network connectivity NB-IoT NB-IoT
GNSS (outdoor) GPS + GALILEO GPS + GALILEO
Wi-Fi positioning Not included ✓ Wi-Fi 2.4 GHz+
BLE beacons (indoor) Sensolus beacons Sensolus beacons
High-precision indoors Compatible anchors ✓ Quuppa-tested+
Temperature sensor Not included ✓ ±0.25 °C built in+
Shock detection Not included ✓ Configurable over the air+
External BLE sensors Not included ✓ Temp, humidity, level and more+
Activity · Orientation · Tamper 3 sensors 3 sensors
Battery Li-SoCl₂ · 10,500 mAh · Replaceable Li-SoCl₂ · 10,500 mAh · Replaceable
Battery life 5 to 10 years 5 to 10 years
Casing & dimensions 130×72×36 mm · 212 g · IP68/IP69K · IK09 130×72×36 mm · 212 g · IP68/IP69K · IK09
Certifications CE · FCC · BT 5.0 CE · FCC · IC · BT 5.0+
OTA firmware NB-IoT + BLE NB-IoT + BLE
Off-network recovery Guaranteed Guaranteed
SaaS platform Identical Identical
Best suited to… Outdoor and in-transit assets · indoor zone positioning through beacons · optimised budget Assets needing temperature, shock, Wi-Fi or external BLE sensors · Quuppa high precision
✓ Choose the ULTRA N if…
  • ·Your assets are mainly outdoors or in transit
  • ·Indoor zone positioning is enough (BLE beacons)
  • ·You do not need temperature or shock measurement
  • ·You are deploying a large number of trackers on a controlled budget
✓ Choose the ULTRA N+ if…
  • ·Your assets move indoors without beacons (Wi-Fi positioning)
  • ·You need to monitor temperature or shock
  • ·You want to connect external BLE sensors
  • ·You need Quuppa-tested indoor precision
See the ULTRA N+ →
Specifications

Full
technical datasheet

Every component optimised for maximum longevity in industrial environments.

TRAKmy ULTRA N 1141 GPS tracker – long-life NB-IoT
Download the datasheet PDF
Weight212 g (7.6 oz)
Dimensions130 × 72 × 36 mm
ColourWhite
Ingress protectionIP68 IP69K
Impact resistanceIK09 · EN 60068
ConnectivityNB-IoT · Europe & USA · No SIM card
GNSSMulti-constellation: GPS + GALILEO
BLEBluetooth Low Energy 5.0
AntennasAll internal · Omnidirectional
BatteryLi-SoCl₂ · 3 cells · Replaceable
Capacity10,500 mAh · 2.94 g of lithium
Battery life5 to 10 years depending on reporting frequency
Off-network recoveryGuaranteed (data recovery)
Temperature-20°C à +60°C
CasingPBT+PC / PBT GF30%+TPE · Flame-retardant · UV-stabilised
ActivationMagnetic · Green / red LED
OTA firmwareNB-IoT + BLE · AES encrypted + signed
EncryptionChaCha20 · Unique keys per device
CertificationsCE FCC BT 5.0 EN 62368 EN 60068
Deployment

Magnetic activation · 3 steps

A single magnet. No tools. No interface. LED feedback shows the status in real time.

1
Tracker with red LED: hold the magnet for 5 seconds
● Red LED
Hold the magnet for 5 seconds

Hold it against the tracker logo. Red LED = activation in progress. Do not remove the magnet.

2
Red and green LED together: remove the magnet
● red + ● green
Red + green LED: remove the magnet

When both LEDs light up at the same time, remove the magnet.

3
Green LED flashing: ready

The tracker is activated and ready to be fitted to your asset.

Field installation tips

Mount as high as possible for better network coverage.
Install vertically, logo facing up, with a clear view of the sky.
Avoid metal or carbon above the tracker, which blocks RF signals.
A flat, clean and degreased surface for optimal adhesion.
🌡
On metal exposed to sunlight: add a thermal insulator underneath (wood, plastic).
💧
Avoid low points where water collects, even with IP69K.
⚠ Possible NB-IoT delay

If "online" does not appear within 5 minutes, hold the magnet against the tracker again for 5 seconds. Retry every 5 minutes. The tracker retries automatically after 24 hours.

Services

Remote management & OTA

The ULTRA N is managed entirely from the platform, with no physical handling.

01
Diagnostics
  • Battery life prediction
  • Detailed energy consumption
  • Positioning diagnostics
  • NB-IoT network quality
  • Installation status
02
Remote management
  • OTA firmware over NB-IoT + BLE
  • Full OTA configuration
  • Tracker usage profiles
  • BLE sensor management
  • Time synchronisation
03
Application services
  • Location & journeys
  • Operating hours
  • Orientation & tamper
  • BLE beacon scanning
Certifications

Certified for worldwide use

Europe and North America: every certification for a frictionless rollout.

CE
European Union
FCC
United States
IP68
Prolonged immersion
IP69K
High-pressure jet
IK09
10-joule impact
BT 5.0
D068598
EN 62368
Electrical safety
EN 60068
Shock & vibration

Field installation

6 mounting options

From permanent high-strength mounting to instant temporary fitting.

Mounting holes: 2 positions · 115 mm apart · 7×9 mm openings
🔩
Rivets
Permanent fixing

Quick, permanent fitting through the 2 mounting holes (115 mm apart, 7×9 mm openings). Ideal on skips, metal crates and perforated structures.

PermanentQuick fitting
🔩
Screws & nuts
Removable fixing

Bolted through the casing eyelets. Removable with standard tools. Suited to flat, drillable surfaces (metal, wood, composite).

RemovableFlat surfaces
🪢
Cable ties
Tubes · Bars · Profiles

Plastic or stainless steel ties passed through the tracker eyelets. Compatible with tubes, bars, frames and profiles of any section. Drill-free fitting.

Drill-freeVersatile
🏭
Industrial adhesive
Non-drillable surfaces

High-strength structural adhesive (Tec7 X-Tack type). The casing bonds directly to clean, degreased surfaces. Resistant to weather and vibration.

⚠ Difficult to remove once cured.

StructuralAll surfaces
🧲
Magnetic mounting kit
Removable · Instant

A magnetic plate screwed onto the casing. Fitted and removed in seconds on any ferrous surface. Ideal for shared assets or frequent rotation.

RemovableSteel · Ferritic stainless
🏷️
Double-sided tape
Drill-free · Smooth surfaces

High-strength double-sided adhesive foam applied under the casing. Permanent adhesion on plastic, painted metal and composite. UV and weather resistant.

⚠ Degrease the surface before fitting.

Drill-freeUV-resistant
SaaS platform

Say goodbye to
spreadsheets & logbooks

The TRAKmy platform turns your assets' location and activity data into concrete, actionable information. Accessible to everyone, with no IT skills required.

Your trackers send their data straight to the platform. A powerful search engine, visual dashboards and automatic alerts give you full visibility over your fleet.

TRAKmy platform interface – asset map
Asset map
Find any asset in seconds. Fast search, filters by zone, status or equipment type.
Dashboards
Visualise the utilisation, inventory and activity of your assets. Customisable and exportable dashboards.
Automatic alerts
Get a notification as soon as an asset moves unexpectedly, exceeds a threshold or leaves a geofence.
Secure data
Single Sign-On with your corporate credentials. Granular access control by team or role.
ERP & API integration
Connect your existing ERP through an open API. Enrich the platform with your business data (shipments, vehicles, and more).
Mobile app
Manage your assets in the field. Tracker activation, proximity search, inspection and alerts, on iOS and Android.
Tracker management

Manage your trackers
from your desk

Remote firmware updates (OTA), reconfiguration, battery diagnostics and network quality: everything is done from the platform. No physical intervention required.

Simultaneous OTA update across every tracker
Battery life prediction per tracker
NB-IoT network quality and GPS accuracy
Automatic recovery of offline data
OTA
Contactless updates
Auto
Offline data recovery
5 years
Min. battery life
SSO
Secure sign-in
Subscriptions

Choose your plan

Essential
  • Map & journey history
  • Basic geofences & entry/exit alerts
  • iOS & Android mobile app
  • Customisable dashboards
  • Pull & Push API
  • 12-month data retention
  • 50 geofences · 10 alerts
Learn more →
Analytics
  • Everything in Professional +
  • Utilisation & occupancy KPIs
  • Fleet dashboards & predictive maintenance
  • Historical playback & process flows
  • Power BI & IFRAME · custom reports
  • 36-month retention · 200 geofences · 50 alerts
Learn more →
Getting started

Book a demo
with our experts

In 30 minutes, our experts will configure the solution that fits your assets and your objectives with you.

A demo tailored to your industry
Live platform configuration
Mounting and field deployment advice
Quote within 24 hours
No commitment

No posts found!